Technical Discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Replacing starter battery by blair » Thu, 07/25/2019 - 05:14 |
3 |
by Terrapin Thu, 02/12/2026 - 09:47 |
|
|
Port bulk head repair by bsimpson » Thu, 01/15/2026 - 17:08 |
2 |
by McNallybj Tue, 02/10/2026 - 14:55 |
|
|
Rigging Refresh — Thoughts & Advice on MLX3, VPC, D2, Tyrus? by Burnt End » Sun, 02/08/2026 - 11:11 |
0 |
by Burnt End Sun, 02/08/2026 - 11:11 |
|
|
Sink drain lines by dsp36 » Sun, 01/11/2026 - 14:52 |
13 |
by dpower Sat, 01/31/2026 - 13:58 |
|
|
inverter/charger mounting - where did you put yours & what would you change? by Burnt End » Mon, 01/19/2026 - 11:01 |
6 |
by Sojourn Sat, 01/31/2026 - 13:20 |
|
|
Traveler Riserer Leak by Burnt End » Sat, 01/03/2026 - 16:49 |
0 |
by Burnt End Mon, 01/26/2026 - 16:15 |
|
|
Water heater leaking coolant by breitz » Wed, 01/07/2026 - 04:45 |
4 |
by Haro Thu, 01/08/2026 - 13:03 |
|
|
Replacing Mast Base Turning Blocks by Burnt End » Sun, 12/28/2025 - 13:41 |
2 |
by Burnt End Sat, 01/03/2026 - 18:38 |
|
|
Diesel in Bilge by btasquared » Thu, 12/25/2025 - 14:33 |
2 |
by dsp36 Sat, 01/03/2026 - 13:44 |
|
|
The First Cup of Coffee That Felt “Different” by Judson Henkey » Thu, 01/01/2026 - 22:43 |
0 |
by Judson Henkey Thu, 01/01/2026 - 22:43 |
|
|
Re: replacing missing or broken Catalina logo/emblem by Doctor Shredd » Thu, 12/25/2025 - 13:09 |
0 |
by Doctor Shredd Thu, 12/25/2025 - 13:09 |
|
|
Engine Blow-by venting to air filter by Stray1235 » Fri, 12/05/2025 - 06:08 |
6 |
by True Wind Tue, 12/16/2025 - 05:52 |
|
|
Oberdorfer Seals Alternative by Haro » Sat, 12/13/2025 - 16:59 |
0 |
by Haro Sat, 12/13/2025 - 18:13 |
|
|
Electrical isolation of heat exchanger by John Hopkins » Sun, 11/23/2025 - 12:21 |
3 |
by John Hopkins Fri, 11/28/2025 - 05:02 |
|
|
Mk 1.5 stern rail 'remodeling' questions, with davits by C36CC » Sun, 11/16/2025 - 07:52 |
1 |
by pkeyser Thu, 11/27/2025 - 19:12 |
|
|
Extended Cable length for new depth sounder transducer by pkeyser » Mon, 11/17/2025 - 06:46 |
1 |
by Haro Fri, 11/21/2025 - 13:50 |
|
|
C36: Downhall and Vang-when do I need both? by UtahGene » Thu, 06/12/2025 - 10:34 |
3 |
by EUREKA Wed, 11/19/2025 - 16:08 |
|
|
Universal M35 injectors by EUREKA » Wed, 11/12/2025 - 11:38 |
5 |
by EUREKA Sat, 11/15/2025 - 18:17 |
|
|
Bilge pump hose by stephenemmerman » Sat, 11/15/2025 - 05:55 |
0 |
by stephenemmerman Sat, 11/15/2025 - 05:55 |
|
|
Macerator Pump fuse by Roland » Fri, 06/11/2010 - 22:10 |
9 |
by thisoldfish Wed, 11/12/2025 - 04:06 |
|
|
Rudder Post Leak by benethridge » Fri, 04/05/2013 - 18:26 |
6 |
by compassrose888 Mon, 11/10/2025 - 11:34 |
|
|
Adler Barbour (Dometic) Cold Machine by tangled » Fri, 05/19/2017 - 06:43 |
17 |
by Ken Krawford Wed, 10/22/2025 - 09:56 |
|
|
Temp Guage Pegging by pierview » Mon, 06/23/2025 - 14:19 |
4 |
by John Robb Sat, 10/11/2025 - 06:51 |
|
|
How to read the M35B Tranny Dip Stick, and by Bruce Stanley » Wed, 11/19/2014 - 22:56 |
7 |
by alfricke Mon, 10/06/2025 - 17:02 |
|
|
Hurth Transmission - bent fingers on coupling by down_shift » Tue, 05/03/2016 - 18:25 |
9 |
by GaryB Fri, 08/29/2025 - 17:42 |
Log in to post new content in the forum.